Finn Goheen

Peugeot 208 Key Replacement

It is better to leave the replacement of Peugeot 208 keys to auto locksmiths who have the equipment and knowledge. They can design and program keys faster and cheaper than dealers.

If your key fob has stopped locking or unlocking your doors, it is likely due to a dead coin battery. But, there are other reasons that the key may be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also preventing it from starting the engine. In this scenario you'll have to employ the alternate method of starting as described in your vehicle's owner's manual.

The spark plugs might also be worn out. Spark plugs are what ignite the fuel to start the engine. However, they have a limited life span. If they aren't used enough, they will eventually fail.

Luckily, there is an easy solution for this problem. The best way to solve this issue is to determine the voltage of your car battery with a multimeter. If it's below 11.5 volts, then you need to replace it. It is also important to clean the battery's contacts in the event that it is damaged by corrosion. This can be done by lifting the rubber covers that protect both battery terminals and using wire brushes to clean any corroded components of the battery. Then, reconnect the positive and negative pole cables.

Water Damage

If your 208 will not start and the battery hasn't gone flat, you should check the spark plugs. It could be that they are simply too dirty and do not spark. The spark plugs can be cleaned in a workshop.

Peugeot cars use a transponder style key that works with the car's ignition system. This guarantees that only the right key can start the engine. If the chip in the Peugeot key is damaged, it will not transmit the proper signal to the vehicle.

Water damage is a common cause of this problem. This is particularly prevalent in colder climates, where the vehicle may have been exposed to rain or snow. If this is the case, get in touch with a reputable locksmith who will have all of the tools and equipment required to change the key's programming. They will also have the latest technological know-how to get a new peugeot car key (read this blog post from Telegra) and the equipment required to create the Peugeot 208 smart key. The process shouldn't be more than 15 minutes.

Contacts of the battery may be damaged.

peugeot 206 key fob replacement replaced the old transponder chips with a new version that makes use of electronic components mounted on a circuit board. The new system is excellent when it's new, however the circuit boards deteriorate over time and stop working properly.

This could stop the immobiliser chip from triggering which means that your car won't start. If this is the case, it's best to contact a peugeot 206 key replacement specialist or locksmith.

Another common issue is when the battery in the key fob begins to fail, which causes the key blade to stop being able to feed into the lock. A locksmith in your car will replace the battery and then cut a new blade for you. This is a quick solution.

Faulty Receiver Module

If your peugeot 406 remote key programming key fob has stopped working after dropping it on the floor, getting exposed to a sudden downpour or accidentally washing it or washing it, it could be due to a defective receiver module. The receiver is responsible for transmitting radio frequency signals to an on-board computer, which controls the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals which prevent water from getting to the electronic chip inside. Water can damage the chip when it is exposed to the water for an extended period of time. Submerging the key fob into ocean water at the beach or throwing it into the water can be especially damaging because of the high salt content.

The module will need to be replaced if the Peugeot spare key is no longer working. This can only by done by a Peugeot specialist or a professional auto locksmith. Peugeot keys, unlike other cars, are secured by an immobilizer device. This requires the correct code to begin the car. It is for this reason that you should only rely on the Peugeot locksmith to create and program the replacement.

Computer with a problem on board

The on-board computer in your peugeot 206 key is responsible for a number of the systems within your vehicle, from power windows to the airbags. When something goes wrong in these systems, it will typically display a code that identifies the problem. This code will be saved within the system until the problem is resolved. Often, this will involve replacing the computer on board.

One of the main causes of the airbag light flashing is loose or corroded connections in the airbag sensor. This can occur due to wear and tear, ageing or exposure to moisture and salt. It is essential to have this issue resolved as soon as possible, since an airbag that is not functioning properly could be dangerous in the event of an accident.

If your Peugeot is showing a card not detected error, the battery in the key fob might be weak or dead. This can prevent the key fob from transmitting a signal that will disable your vehicle's immobilizer. Try this by pressing the unlock key on the fob's key, then trying to start your vehicle. If this fails, the key battery needs to be replaced.