Russell Nye

How to repair bifold door top pivot bifold door top roller (Read More Listed here) Guide

If your bifold door is sticking then it's likely that they require some maintenance. You may need to clean or lubricate them, or even adjust them. The issue could be caused by an unfastened bolt on the top pivot or by the top guide roller.

This kit includes all the necessary hardware to return your bi fold repairs-fold closet door system to optimal performance.

Take the door off

Installing an interior set of bifold doors could seem like an involved and complicated project however, it's actually easy for DIYers with a bit of experience. Moving the frame isn't the problem but the trick is getting the doors to bi fold door repair and close quickly and accurately. Bifold doors are intricate pieces of machinery, and as such they may require some tuning up to ensure that they function properly. It could be as easy as tightening up a screw, or as complicated as taking out and replacing the door's pivot pin or roller.

You can usually resolve these issues with a few simple adjustments, without having to take out the doors. You might find that your doors are sagging, scraping the floor, or they are bouncing off of their track. It's not difficult to fix these issues. Follow these three easy steps and your bifold door should be back in line in the shortest amount of time.

One of the most frequent problems that internal bifold doors encounter is sliding out of alignment. This can be due to loose screws, holes on the anchor/pivots or an unaligned bifold door. The majority times, this can be corrected with a few simple adjustments. However, if your door doesn't move at all, you may need to replace it.

To open the door to open it, you'll require an screwdriver and perhaps pliers (to assist in loosening any pins on the pivot that are stuck). The screwdriver can be used to loosen the locking levers at the bottom bracket for pivots. The pliers are used for removing the pin.

Once the top roller is free it should be possible to raise the door and swivel it downward, allowing you to take it off of its pivot brackets and track. It's usually a simple procedure, but you need to be cautious not to let the door strike the frame of the door. Then, you can sand down the edge of the door to make it smooth. Then paint or refinish the door if necessary.

Take off the Roller Guide

This spring-loaded roller guide is mounted on the top of bifold doors to aid in smooth operation. It is designed to work with Kenna frames and will fit door panels ranging from 1 inch to 1-3/8 inches thick. It is constructed of steel, nylon and plastic components. It is able to replace a damaged guide.

Take out any screws that are holding the guide to the roller using a screwdriver. Make use of your hands to gently pull it from the frame. It could require some effort to take off the door, so you may need an assistant to help.

After the guide has been removed, carefully cut the remaining finish around the foot of the new guide with a sharp blade to separate it from the rod blank. This will make the guide foot easier to remove and also prevent any damage. Be careful when doing this as the foot is extremely sharp and can cut or snag your fingers.

You may need to apply some force to remove the guide, but be careful not to chip or break the foot. After you've removed the guide from the rod blank, be sure to remove all of the threads and epoxy remaining in the area where it was affixed. This will help prevent any future problems with the guide.

After you have removed the previous guide, test your replacement by putting it in its permanent location. Make a few turns with masking tape or guide tubing in order to secure it in its place. This allows you to double check the alignment of the guide and spacing to make sure everything is properly set up. Whether you're eye-balling it or using the always accurate CRB Spine Finder and Deflection System it is essential to avoid any problems in the future.

The last step is to replace the door. If the guide is in the correct position and functions just as it should, you're able to proceed. Remember to tighten and replace any screws or pins you removed or loosened.

Remove the Bottom Pivot

Bifold doors can be a beautiful addition to any home, but they may need to be tweaked or adjusted to keep them in good working order. While some of the more straightforward issues can be fixed with the doors still in place, others will require removal. This guide will guide you through the steps to remove internal bifold door pivots, pins and rollers so that you can make your doors slide like new.

Gathering your tools is the first step. Getting everything together ahead of time will make it easier later on in the project. You'll need a screwdriver, pliers and perhaps a wrench. A set of basic tools is available at a reasonable price from a local hardware store. It's important to keep some wood glue on hand. This is useful when you need to put the rollers in their place.

After gathering your tools and tools, open the bifold door and loosen the top track bracket with your screwdriver. Once this is loose the door should be free to slide off the top track completely. It might take a bit of jiggling but it should pop right off the track.

The pivot on the bottom of the frame needs to be removed. Close all doors to the interior before beginning. This will make it easier to do than trying to work inside. If the track on the bottom is in good shape you'll be able to lift the door and remove the track.

If the track is damaged, then you'll need to replace it. Hardware stores sell replacement tracks for bifold doors, as well as swinging closet doors. If the track is seriously damaged, then you might need to replace it entirely.

After your track has been repaired or replaced You'll need to check the doors for proper operation. Make sure they're able to move smoothly between positions. You'll want to ensure that the edges of your door are parallel with the frame when closed. If they aren't, you'll need to adjust the top pivot bracket while tightening or loosening the bottom setscrew.

Replace the Roller

Bifold doors can be used to neatly cover closets, laundry nooks and pantries, but only if they work properly. The bifold doors consist of two panels that are hinged and slide along an incline at the top of the frame. Over time the roller guides may wear out and cause the doors to sag. The guide roller can be replaced in a matter of minutes using a few tools.

The first step is to remove the guide roller from the door panel. This requires taking off the pivot bolt at the bottom and loosening the screw that holds the guide at its top. After taking off the guide, pull the panel out of the track. Then with a wrench, remove the top pivot bolt from the hole in the frame's header by loosening the bolt.

A top nylon replacement guide with a 7/8 inch diameter wheel and a base made of steel is available from Stanley, Cox or Acme. It mounts on the top edge of a bifold door that is 1 to 1-3/8 inches in thickness and is spring loaded to self-adjust the upper track to ensure smooth glide.

A bifold door may also scratch the floor when it closes and opens. This can happen after adding carpet, or other flooring materials which require the doors be slightly raised to allow for clearance. Removal of the screw that adjusts the bottom pivot and loosening the top track's mounting screws, and moving the anchor pin typically enough to resolve this issue.

A set top roller with new guides can be an inexpensive solution to your bifold doors becoming difficult to operate. They are usually available at your local hardware store in the door section, however, they are also available on the internet through a variety of sellers. In addition to a brand-new top guide for rollers, you'll require a small bottle of Elmer's wood glue which is sold in the big box stores, as well as a squeeze clamp. The clamp assists in keeping the repair bifold door bottom pivot area tightly after glue is inserted and allowed to dry.